Electro Industries Shark 200T Spécifications Page 222
- Page / 298
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
B: Modbus Map and Retrieving Logs
Doc# E149701 MM-22
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Description (Note 1) Format Range (Note 6) Units or Resolution Comments # Reg
Modbus Address
Hex Decimal
4E2B - 4E2B 20012 - 20012 Reset Option Card 1 Input Accumulators UINT16 password (Note 5) 1
4E2C - 4E2C 20013 - 20013 Reset Option Card 1 Output Accumulators UINT16 password (Note 5) 1
4E2D - 4E2D 20014 - 20014 Reset Option Card 2 Input Accumulators UINT16 password (Note 5) 1
4E2E - 4E2E 20015 - 20015 Reset Option Card 2 Output Accumulators UINT16 password (Note 5) 1
Block Size: 16
conditional write
5207 - 5207 21000 - 21000 Initiate Meter Firmware Reprogramming UINT16 password (Note 5) 1
5208 - 5208 21001 - 21001 Force Meter Restart UINT16 password (Note 5) causes a watchdog reset, always reads 0 1
5209 - 5209 21002 - 21002 Open Privileged Command Session UINT16 password (Note 5) meter will process command registers (this register
through 'Close Privileged Command Session' register
below) for 5 minutes or until the session is closed,
whichever comes first.
1
520A - 520A 21003 - 21003 Initiate Programmable Settings Update UINT16 password (Note 5) meter enters PS update mode 1
520B - 520B 21004 - 21004 Calculate Programmable Settings Checksum
(Note 3)
UINT16 0000 to 9999 meter calculates checksum on RAM copy of PS block 1
520C - 520C 21005 - 21005 Programmable Settings Checksum (Note 3) UINT16 0000 to 9999 read/write checksum register; PS block saved in
nonvolatile memory on write (Note 8)
1
520D - 520D 21006 - 21006 Write New Password (Note 3) UINT16 0000 to 9999 write-only register; always reads zero 1
520E - 520E 21007 - 21007 Terminate Programmable Settings Update (Note
3)
UINT16 any value meter leaves PS update mode via reset 1
520F - 5211 21008 - 21010 Set Meter Clock TSTAMP 1Jan2000 - 31Dec2099 1 sec saved only when 3rd register is written 3
5212 - 5212 21011 - 21011 Manually Trigger Waveform Capture UINT16 any value applies to Shark 300 only; returns busy exception if
blocked by another capture in progress
1
5213 - 5219 21012 - 21018 Reserved Reserved 7
521A - 521A 21019 - 21019 Close Privileged Command Session UINT16 any value ends an open command session 1
Block Size: 20
read/write
658F - 659A 26000 - 26011 Perform a Secure Operation UINT16 encrypted command to read password or change meter
type
12
Block Size: 12
write only in PS update mode
752F - 752F 30000 - 30000 CT multiplier & denominator UINT16 bit-mapped
dddddddd mmmmmmmm
high byte is denominator (1 or 5, read-only),
low byte is multiplier (1, 10, or 100)
1
7530 - 7530 30001 - 30001 CT numerator UINT16 1 to 9999 none 1
7531 - 7531 30002 - 30002 PT numerator UINT16 1 to 9999 none 1
7532 - 7532 30003 - 30003 PT denominator UINT16 1 to 9999 none 1
7533 - 7533 30004 - 30004 PT multiplier & hookup UINT16 bit-mapped
mmmmmmmm mmmmhhhh
mm…mm = PT multiplier (1, 10, 100, or 1000)
hhhh = hookup enumeration (0 = 3 element wye[9S], 1 =
delta 2 CTs[5S], 3 = 2.5 element wye[6S])
1
Encryption Block
Programmable Settings Section
Basic Setups Block
Privileged Commands Block
- Shark 200 & 200T 1
- Use Of Product for Protection 6
- Statement of Calibration 6
- Disclaimer 6
- Table of Contents 9
- Industries/GaugeTech 10
- 1.1.1: Wye Connection 13
- 1.1.2: Delta Connection 16
- 1.2: Power, Energy and Demand 20
- 1.4: Harmonic Distortion 26
- 1.5: Power Quality 29
- 2.1.2: Ordering Information 34
- 2.1.3: V-Switch 36
- Key Technology 36
- 2.1.4: Measured Values 38
- Table 1: 38
- 2.1.5: Utility Peak Demand 39
- 2.2: Specifications 40
- 2.3: Compliance 45
- 2.4: Accuracy 46
- Table 2: 46
- 3: Mechanical Installation 49
- 3.4: Transducer Installation 54
- 4: Electrical Installation 57
- $VSSFOUHJMMT 60
- OJDLFMQMBUFE 60
- CSBTTTUVET 60
- 5.1.1: IrDA Port (Com 1) 79
- Electro Industries/GaugeTech 80
- UNICOM 2500 83
- Overview 84
- Software 85
- 6: Using the Shark® 200 Meter 103
- 6.2: Using the Front Panel 105
- 6.2.6: Using Operating Mode 117
- 7: Using the I/O Option Cards 121
- 7.2: Installing Option Cards 122
- 7.4: 1mA Output Card (1mAOS) 124
- 7.4.1: Specifications: 124
- 7.4.2: Default Configuration: 125
- 7.4.3: Wiring Diagram 126
- 7.5.1: Specifications 127
- 7.5.2: Default Configuration: 128
- 7.5.3: Wiring Diagram 129
- 7.6.1: Specifications 130
- 7.6.2: Wiring Diagram 132
- 7.7.1: Specifications 133
- 7.7.2: Default Configuration: 134
- 7.7.3: Wiring Diagram 135
- 7.8.1: Specifications 136
- 7.8.2: Wiring Diagram 137
- 7.9.1: Specifications 138
- 7.9.2: Default Configuration 139
- 7.9.3: Wiring Diagram 139
- 7.10.1: Specifications 140
- 7.10.2: Default Configuration 141
- 7.10.3: Wiring Diagram 141
- 8.1: Overview 143
- 8.2: Hardware Connection 143
- 8.4.1: Ethernet Communication 144
- 8.4.2: Embedded Web Server 144
- 8.4.5: Keep-Alive Feature 151
- 9: Data Logging 153
- A.1: Introduction 155
- B.1: Introduction 161
- B.3: Data Formats 161
- B.4: Floating Point Values 162
- Byte 012345678910111213 164
- B.5.3: Block Definitions 166
- B.5.4: Log Retrieval 176
- B.5.4.1: Auto-Increment 176
- B.5.6: Examples 196
- B.6.1: Hex Representation 199
- B.6.2: Decimal Representation 199
- C: DNP Mapping 243
- C.3: Data Link Layer 244
- C.4: Application Layer 244
- C.5: Error Reply 246
- C.6: Object Specifics 246
- C.7: DNP Object Point Map 248
- C.8: DNP Message Layouts 257
- C.9: Internal Indication Bits 260
- D.1: Introduction 261
- D.2: Installation Procedures 261
- Network Card (INP300S) 269
- E.1.5: Reference Materials 280
- Network Card 281
- E.2.1: Overview 281
- System Log 293
- Firmware 294
- E.6: Keep-Alive Feature 296
- E.7: Testing 296
- E.8: Error Codes 297
Produits connexes et manuels pour Multimètres Electro Industries Shark 200T
(246 pages)Bloomfield Accesorios Para Hacer Café manuales de usuario
Empezando en S
Commentaires sur ces manuels